What P0335 means
P means powertrain (engine and transmission). The 0 marks a generic code defined by SAE, so the same number means the same thing across makes. The third character, 3, places it in the ignition system or misfire subsystem; the last two digits identify the specific fault.
The crankshaft position sensor reads a toothed reluctor wheel on the crankshaft and tells the engine computer engine speed and piston position. It is essential: without it, most engines will not run. The same signal also feeds the misfire monitor.
The letter "A" distinguishes between two or more of the same component on one vehicle. Which physical part is "A" is set by the manufacturer, so confirm it in the service information before replacing anything.
What “Circuit” means here
"Circuit" is the broadest fault type in the standard. The module has found the crankshaft position (CKP) sensor circuit electrically unusable: the signal is missing, outside its electrical limits, or the module's own self-test of the circuit failed. Some vehicles set this instead of the more specific low/high codes; others set it alongside them. Either way the first suspect is the wiring and connector, then the component, and only then the module.
What you may notice
Symptoms depend on the vehicle and on how the module responds to the fault. Any of these can accompany P0335:
- Engine cranks but will not start
- Stalling, often when hot
- Tachometer dropping out
- Misfire or hesitation
Causes to consider
- Failed crankshaft position sensor
- Damaged sensor wire near belt
- Broken reluctor ring teeth
Where to start diagnosing P0335
- Inspect the connector and harness; heat and oil contamination are common.
- Check the reluctor wheel and the sensor tip for damage or debris.
- Watch engine RPM in live data while cranking; no RPM reading while cranking points strongly at this circuit.
- On "variation not learned" codes, the manufacturer's crank relearn procedure is usually required after parts replacement.
Clear the code only after recording freeze frame data: it shows the engine speed, load and temperature at the moment the fault set, which is often the best clue to reproducing it.
Live data to watch
These standard OBD2 values relate to P0335. Support varies by vehicle; a value your car does not report will simply be missing.
| Value | What to look for |
|---|---|
| Engine RPM (PID 0x0C) | Should be present during cranking and steady at idle. |
Related codes
Codes from the same crankshaft position (CKP) sensor family. If several are stored together, the shared part — wiring, a common reference voltage, or the component itself — is the place to start.
| Code | Definition |
|---|---|
| P0315 | Crankshaft Position System Variation Not Learned |
| P0336 | Crankshaft Position Sensor "A" Circuit Range/Performance |
| P0337 | Crankshaft Position Sensor "A" Circuit Low |
| P0338 | Crankshaft Position Sensor "A" Circuit High |
| P0339 | Crankshaft Position Sensor "A" Circuit Intermittent/Erratic |
| P0385 | Crankshaft Position Sensor "B" Circuit |
| P0386 | Crankshaft Position Sensor "B" Circuit Range/Performance |
| P0387 | Crankshaft Position Sensor "B" Circuit Low |
Symptoms that lead to P0335
If you have not scanned the car yet, or P0335 is one of several codes stored, these guides start from what the vehicle is actually doing.
Frequently Asked Questions
What does P0335 mean?
P0335 is the generic SAE J2012 code for "Crankshaft Position Sensor A Circuit Malfunction". In plain terms, it means the engine computer has detected a "circuit" fault on the crankshaft position (CKP) sensor.
Can I keep driving with P0335?
A crank sensor fault can stop the engine while driving. Have it repaired before relying on the vehicle.
What should I check first for P0335?
Inspect the connector and harness; heat and oil contamination are common.
Definition source: SAE J2012 / ISO 15031-6 generic DTC definitions. This is the generic meaning that applies across makes; a manufacturer can define a code more narrowly or add its own sub-codes, so confirm against the service information for your vehicle before replacing parts. Written by the OBDAssistant engineering team — see our editorial policy.