U0107

U0107: Lost Communication With Throttle Actuator Control Module

Quick answer: U0107 means another module on the vehicle network stopped hearing from the throttle actuator control module.

Driving: Reduced-power mode or poor throttle response. Because this module is involved in braking, steering, stability or propulsion, have it checked before driving further than you need to.

Read U0107 on your phone OBDAssistant reads codes and live data through a Bluetooth OBD2 adapter.

What U0107 means

U means network (communication between modules). The 0 after it marks a generic code defined by SAE rather than by the manufacturer, and the U01xx block is reserved for lost-communication faults with specific modules.

Modern vehicles connect their control modules on a shared data network, most often CAN bus. Each module expects regular messages from the others. A "lost communication" code is set by a module that stopped receiving expected messages from the named module for longer than an allowed time.

The module named here is the throttle actuator control module. What you notice depends on what that module does: reduced-power mode or poor throttle response.

What “Lost Communication” means here

A module on the network expected periodic messages from the throttle actuator control module and did not receive them for longer than allowed. The code is stored in the module that noticed the silence, not necessarily in the one that went quiet, and the named module may itself be unpowered, faulty, or cut off by wiring.

What you may notice

Symptoms depend on the vehicle and on how the module responds to the fault. Any of these can accompany U0107:

  • Warning lights for the system the missing module controls
  • Features of that system not working
  • Several U-codes stored at once in different modules

Where to start diagnosing U0107

  1. Check battery voltage and the charging system first; low voltage causes many communication faults.
  2. Check whether the named module is powered: its fuses, power feeds and grounds.
  3. Scan all modules: if one module is silent to every other module, focus on it; if many modules are missing, suspect the network wiring.
  4. Inspect network wiring and connectors near the named module; on CAN, the two termination resistors should measure about 60 Ω together across the bus pins with the battery disconnected.

Clear the code only after recording freeze frame data: it shows the engine speed, load and temperature at the moment the fault set, which is often the best clue to reproducing it.

Live data to watch

These standard OBD2 values relate to U0107. Support varies by vehicle; a value your car does not report will simply be missing.

ValueWhat to look for
Control module voltage (PID 0x42)Low system voltage can cause communication faults.
Module listA full network scan showing which modules respond.

Related codes

Codes from the same vehicle network communication family. If several are stored together, the shared network wiring, power supply or ground is the place to start.

CodeDefinition
U0103Lost Communication With Gear Shift Control Module "A"
U0104Lost Communication With Cruise Control Module
U0105Lost Communication With Fuel Injector Control Module
U0106Lost Communication With Glow Plug Control Module
U0108Lost Communication With Alternative Fuel Control Module
U0109Lost Communication With Fuel Pump Control Module
U0110Lost Communication With Drive Motor Control Module "A"
U0111Lost Communication With Battery Energy Control Module "A"

Further reading

Frequently Asked Questions

What does U0107 mean?

U0107 is the generic SAE J2012 code for "Lost Communication With Throttle Actuator Control Module". In plain terms, it means another module on the vehicle network stopped hearing from the throttle actuator control module.

Can I keep driving with U0107?

Reduced-power mode or poor throttle response. Because this module is involved in braking, steering, stability or propulsion, have it checked before driving further than you need to.

What should I check first for U0107?

Check battery voltage and the charging system first; low voltage causes many communication faults.

Definition source: SAE J2012 / ISO 15031-6 generic DTC definitions. This is the generic meaning that applies across makes; a manufacturer can define a code more narrowly or add its own sub-codes, so confirm against the service information for your vehicle before replacing parts. Written by the OBDAssistant engineering team — see our editorial policy.